Aluminium coated film production process


Release time:2024-06-21

Aluminium plating process for plastic films generally adopts the direct plating method, i.e. the aluminium layer is directly plated on the surface of the substrate film.BOPET, BOPA film substrate does not need surface treatment before aluminium plating, and it can be directly vapour plated. While BOPP, CPP, PE and other non-polar plastic films, the film surface needs to be corona treated or coated with an adhesive layer before vapour plating, so that its surface tension reaches 38-42 dynes/cm or has good adhesion. When vapour plating, the roll of film is placed in the vacuum chamber, and the vacuum chamber is closed to draw a vacuum. When the vacuum degree reaches a certain (4×10-4MBA or more), the evaporation boat will be heated up to 1300°C~1400°C, and then the aluminium wire with purity of 99.9% will be continuously fed to the evaporation boat. Adjust the unwinding speed, winding speed, wire feeding speed and evaporation amount, open the cooling source, so that the aluminium wire in the evaporation boat continuous melting, evaporation, so as to form a layer of bright aluminium layer in the surface of the moving film after cooling that is aluminium coating film.

Vacuum Evaporation Principle

The coated film substrate (cylinder) is mounted in the vacuum evaporation plating machine, vacuum pump is used to draw vacuum, so that the vacuum degree in the coating reaches 1.3×10-2~1.3×10-3Pa, and the crucible is heated to make the high-purity aluminium wire melt and evaporate into gaseous aluminium at a temperature of 1200℃~1400℃. The gaseous aluminium particles are deposited on the surface of the moving thin film substrate and reduced by cooling to form a continuous and bright metallic aluminium layer. By controlling the evaporation rate of aluminium metal, the moving speed of the film substrate and the vacuum of the coating chamber to control the thickness of the aluminium layer, the general thickness of the aluminium layer is 25~500nm, the width of the aluminium film is 800mm~2000mm.

Vapour plating method: in the substrate surface vapour plating of aluminium method has a direct vapour plating method and transfer method two kinds.

(1) direct vapour deposition method. Is the town substrate directly through the vacuum coating machine, the metal aluminium vapour plating on the surface of the substrate and the formation of aluminium film. Direct vapour deposition method on the substrate of higher requirements, especially to form a bright surface metal film, must require the substrate has a good surface smoothness. If the surface of the paper is rough, to use direct vapour deposition, the surface needs to be coated before aluminising. In addition, the volatiles of the substrate during the vapour deposition process should be low. Therefore, the direct vapour deposition method has greater limitations on the substrate, it is mainly suitable for vapour deposition of plastic films, can also be used for the vapour deposition of paper, but the quality of the paper is required to be high, and a certain limit on the amount of paper.

(2) Transfer method. Is with the help of carrier film (vacuum aluminising film) to transfer the metal aluminium layer to the surface of the substrate and the formation of aluminised film. Transfer method is in the direct evaporation method on the basis of the development of a new process, it overcomes the direct evaporation method of the limitations of the substrate requirements, especially suitable for aluminium plating in a variety of paper and cardboard, but also can be used for aluminium plating of plastic films. Foreign countries have been transfer method applied to cloth, fibre, leather and other substrates on the aluminium-plated products. Our country mainly adopts the transfer method to produce aluminised paper. [1]

Aluminium-plated film production process:

Substrate unwinding → vacuum → heating evaporation boat → send aluminium wire → evaporation → cooling → thickness measurement → spreading → roll up

Hubei Jinde Packaging Co., Ltd.

| “Preferred Supplier Of Color Printing Packaging Solutions”

Contact Us

Contact: Ms Zhang

Cell: +86 15807178126

E-mail: scarlette@jindepack.com

Add: Changxing Road No.2, Xiaonan Economic Development Zone, Xiaogan City,Hubei, China

%{tishi_zhanwei}%

Welcome to leave an online message, we will contact you promptly

%{tishi_zhanwei}%